Thursday, 9 July 2015

Tire Size Guide


The tire size branded on the sidewall provides a significant amount of information about the tire's intended purpose, dimensions, load capacity and high temperature/high speed durability.
Our primary example will be based on variations of the 225/50R16 size, although other sizes will appear where appropriate.
"The tire size branded on the sidewall provides a significant amount of information about the tire's intended purpose, dimensions, load capacity and high temperature/high speed durability."

Service Type

Most tire sizes begin with a letter or letters that identify the type of vehicle and/or type of service for which they were designed. The common indicators are as follows:
P225/50R16 91S
P = When a tire size begins with a "P," it signifies the tire is a "P-metric" size that was designed to be fitted on vehicles that are primarily used as passenger vehicles. This includes cars, minivans, sport utility vehicles and light duty pickup trucks (typically 1/4- and 1/2-ton load capacity). The use of P-metric sizes began in the late 1970s and they are the most frequently used type of tire size today.
225/50R16 92S
If there isn't a letter preceding the three-digit numeric portion of a tire size, it signifies the tire is a "Metric" size (also called "Euro-metric" because these sizes originated in Europe). While Metric tire sizes are primarily used on European cars, they are also used on vans and sport utility vehicles. Euro-metric sizes are dimensionally equivalent to P-metric sizes, but typically differ subtly in load carrying capabilities.
T125/90D16 98M
T = If a tire size begins with a "T," it signifies the tire is a "Temporary Spare" ("space saver" or "mini spare") that was designed to be used temporarily only until a flat tire can be repaired or replaced.
LT245/75R16 108/104S
LT = If a tire size begins with "LT," it signifies the tire is a "Light Truck-metric" size that was designed to be used on vehicles that are capable of carrying heavy cargo or towing large trailers. This includes medium and heavy-duty (typically 3/4- and 1-ton load capacity) pickup trucks, sport utility vehicles and full-size vans. Tires branded with the "LT" designation are the "little brothers" of 18-wheel tractor-trailer tires and are designed to provide substantial reserve capacity to accept the additional stresses of carrying heavy cargo.
7.50R16LT 112/107Q, 8.75R16.5LT 104/100Q or 31x10.50R15LT 109Q
LT = If a tire ends with "LT," it signifies the tire is either an earlier "Numeric", "Wide Base" or "Flotation" Light Truck size designed to be used on vehicles that are capable of carrying heavy cargo and towing trailers (Numeric sizes), use 16.5-inch diameter rims (Wide Base sizes) or are wider, over sized tires designed to help the vehicle drive on top of loose dirt or sandy surfaces (Flotation sizes). This includes light, medium and heavy duty (typically 1/2-, 3/4 and 1-ton load capacity) pickup trucks and sport utility vehicles. Tires branded with the "LT" at the end of their size designation are also the "little brothers" of 18-wheel tractor-trailer tires and are designed to provide substantial reserve capacity to accept the additional stresses of carrying heavy cargo.
195/70R15C 104/102R
C = If a Euro-metric sized tire ends with a "C," it signifies the tire is a "Commercial" tire intended to be used on vans or delivery trucks that are capable of carrying heavy loads. In addition to being branded with the "C" in their size, these tires are also branded with their appropriate Service Description.
ST225/75R15
ST = If a tire size begins with "ST," it signifies the tire is a "Special Trailer Service" size that was designed to only be used on boat, car or utility trailers. ST-sized tires should never be used on cars, vans or light trucks.

Section Width

Following the letter(s) that identify the type of vehicle and/or type of service for which the tire was designed, the three-digit numeric portion identifies the tire's "Section Width" (cross section) in millimeters.
P225/50R16 91S
The 225 indicates this tire is 225 millimeters across from the widest point of its outer sidewall to the widest point of its inner sidewall when mounted and measured on a specified width wheel. This measurement is also referred to as the tire's section width. Because many people think of measurements in inches, the 225mm can be converted to inches by dividing the section width in millimeters by 25.4 (the number of millimeters per inch).
225mm / 25.4 = 8.86"

Sidewall Aspect Ratio

Typically following the three digits identifying the tire's Section Width in millimeters is a two-digit number that identifies the tire's profile or aspect ratio.
P225/50R16 91S
The 50 indicates that this tire size's sidewall height (from rim to tread) is 50% of its section width. The measurement is the tire's section height, and also referred to as the tire's series, profile or aspect ratio. The higher the number, the taller the sidewall; the lower the number, the lower the sidewall. We know that this tire size's section width is 225mm and that its section height is 50% of 225mm. By converting the 225mm to inches (225 / 25.4 = 8.86") and multiplying it by 50% (.50) we confirm that this tire size results in a tire section height of 4.43". If this tire were a P225/70R16 size, our calculation would confirm that the size would result in a section height of 6.20", approximately a 1.8-inch taller sidewall.

Internal Construction

A letter (R in this case) that identifies the tire's internal construction follows the two digits used to identify the aspect ratio.
P225/50R16, P225/50ZR16
The R in the P225/50R16 91S size identifies that the tire has a Radial construction in which the tire's body plies "radiate" out from the imaginary center of the wheel. Radial tires are by far the most popular type of tire today representing over 98% of all tires sold.
If the R in the size was replaced with a D (225/50D16), it would identify that the internal tire body plies crisscross on a Diagonal and that the tire has a "bias ply" construction. Tires using this construction are for light truck and spare tire applications.
If the R in the size was replaced with a B (225/50B16), it would identify that the tire body plies not only crisscross the tire on a diagonal as before, but that they are reinforced with belts under the tread area. This type of tire construction is called "Belted." Tires using this construction are practically extinct.
The European Tyre and Rim Technical Organisation (ETRTO) has adopted branding standards that allowed tire manufacturers to identify tires with self-supporting run-flat constructions within the tire size designation. Self-supporting run-flat tires may be identified with the letter F immediately following the traditional letter identifying tire construction (such as the R designating radial) within the size.
This results in size designations such as 225/45RF17 91Y (for self-supporting run-flat tires that have a speed rating identified in their Service Description and 255/40ZRF20 (for Z-speed rated self-supporting run-flat tires in which the speed rating is contained in the tire size).
Since this tire size designation was adopted well after the introduction of self-supporting run-flat tires into the marketplace, self-supporting run-flat tires introduced and produced before it went into effect will not be required to be branded as such.

Speed Rating

Today, the only tires that continue to include the speed rating "in" the tire size (P225/50ZR16) are Z-speed rated tires. In this case, following the two digits used to identify the aspect ratio are the lettersZR to identify the tire's speed rating (Z) and its internal construction (R). Since 1991, all other speed ratings are identified in the tire's Service Description (which will be covered shortly).

Tire and Wheel Diameter

P225/50R16 91S
The 16 indicates the tire and wheel diameter designed to be matched together.
Tires that have a rim diameter expressed in inches (P225/50R16, as well as 8, 10, 12, 13, 14, 15, 17, 18, 19, 20, 22, 23, 24, 26 and 28) are called "inch rim" sizes. These are the most common types of tire sizes and are used on most cars, minivans, vans, sport utility vehicles and light duty light trucks.
While not as common, two additional "unique" types of tire/wheel diameters are still in use today.
Tires and wheels that have a rim diameter expressed in "half" inches (8.00R16.5LT, as well as, 14.5, 15.5, 17.5 and 19.5) are used on some heavy-duty trailers, heavy-duty light trucks and box vans.
Tires and wheels that have a rim diameter expressed in millimeters (190/65R390, as well as, 365 and415) are called millimetric sizes. Michelin initiated millimetric sizes for their TRX tires that saw limited use on many different car models in the late 1970s and 1980s.
Michelin PAX System run-flat tires have been introduced as an integrated wheel/tire system on a very limited basis as Original Equipment (O.E.) in North America. An example PAX System size of 235/710R460A 104T expresses tire and wheel dimensions in millimeters (235 mm Section Width, tire Overall Diameter of 710 mm and a 460A mm rim diameter, with the "A" in 460A signifying these tires feature "asymmetric" beads in which the outside bead (450 mm) and inside bead (470 mm) are actually different diameters.
All of these "unique" tire/wheel diameters were developed specifically because the tire and wheel design or intended vehicle use required them to be different than conventional tires and wheels. All of these tires and wheels feature bead profiles that have a different shape than traditional "inch rim" sizes.
Tires and wheels with unique rim diameters should never be combined with traditional "inch rim" tires and wheels.
It is critical that the tire and wheel diameters are always confirmed to match before the tire is mounted on the wheel.

Saturday, 4 July 2015

Do you understand what type of spare tyre is in your trunk?

If you ever visit an auto museum, you'll see most antique cars were equipped with two or more spare tires. Fortunately today's roads and improved tire durability have reduced that necessity, allowing our vehicles to be equipped with a single spare or none at all!
While some of today's vehicles are equipped with spares that match the other tires and wheels on the vehicle, they are in the minority. Now most vehicles are originally equipped with a "temporary-use" spare tire and wheel that probably differs in size and construction from the other tires and wheels on the vehicle. And some vehicles are even delivered without a spare tire and wheel thanks to the extended mobility provided by modern run-flat tires or temporary repair and inflation systems, like the ContiComfortKit.

Full-Size Matching Spare Tires and Wheels

While full-size matching spare tires and wheels require the greatest amount of storage space, they are the most versatile. Full-size matching spare tires and wheels should be integrated into the vehicle's tire rotation pattern from the beginning. This will essentially create a set of five tires that will last longer than just four, as well as will "wear out" the spare tire before it "ages out." If the vehicle has all-wheel or four-wheel drive, the spare tire will remain at a similar tread depth to the other tires on the vehicle, reducing driveline stress when called into service. Additionally, when it is time to replace the vehicle's tires, they can be replaced as a set of five allowing you to benefit from using the latest tire technology or select a more desirable tire size that fits the original wheels.

Many of today's spare tires are temporary spare designs intended to get the vehicle to a trained tire service person to repair or replace the tire that's been punctured or damaged.

Full-Size Temporary Spares

Full-size temporary spare tires and wheels match the vehicle's original tire dimensions, but typically feature lighter-weight construction and a shallower tread depth to reduce vehicle weight to improve fuel economy and make the spare easier to install. While most of today's vehicles are originally equipped with alloy wheels, full-size temporary spares are typically mounted on steel wheels and should be used only as spares.

Temporary/Compact Spares

Temporary/Compact Spare tires are physically shorter and narrower than the vehicle's standard tires and wheels. Their smaller dimensions require they operate at higher inflation pressures (typically 60 psi) than standard tires. Temporary/Compact Spares also feature lighter-weight construction and a shallower tread depth than standard tires to reduce vehicle weight, as well as allow more trunk space to be dedicated to luggage. The compact temporary spare tire and wheel that comes with a vehicle is designed to fit that vehicle only. Never attempt to use a Temporary/Compact Spare Tire and wheel on another vehicle unless it is the exact same make and model.

Folding Temporary Spares

While folding temporary spare tires have been installed in vehicles previously, they have extremely limited application today. Folding spares provide the greatest space savings but are more complex to use because they must be inflated with an air pump or a canister of pressurized air prior to use.

The Following Tips Can Help Make Sure That Your Spare Is Used Correctly and Safely

Learn how to install the spare on your vehicle before you have to. Learn how to access the spare tire, jack, lug wrench and wheel lock key (if equipped). Confirm where the jack is to contact the vehicle and practice changing a tire. This will make it a lot easier on that cold, dark rainy night when your vehicle has a real flat.
All temporary spare tires are designed for short-term use only; they are not designed with the same capabilities in terms of load capacity, speed capability, or all-weather traction.
Always check your vehicle's owner's manual and the temporary spare's sidewall for instructions on proper use. It is also important to recognize that controlling a vehicle may be more difficult when using a temporary spare, and temporary spare tires are usually accompanied with warnings that advise against towing a trailer, or traveling over 50 miles per hour for further than 50 miles.
Check the spare tire's air pressure with a tire pressure gauge on a monthly basis, when you check all other tires on the vehicle. There's nothing more aggravating than a flat spare when you have a flat tire.
Always confirm the inflation pressure before use and ensure that your spare has the manufacturer recommended inflation. It's important to check and adjust the temporary spare's inflation to the recommended pressure before driving away.

Friday, 26 June 2015

Where to Install New Pairs of Tires?

Most vehicles are equipped with the same size tire at every wheel position. Ideally all of these tires should also be of the same type and design, have the same tread depth and be inflated to the pressures specified by the vehicle placard or owner's manual. This combination best retains the handling balance engineered into the vehicle by its manufacturer.
However due to a front-wheel drive vehicle's front tires' responsibility for transmitting acceleration, steering and most of the braking forces, it's normal for them to wear faster than rear tires. Therefore if the tires aren't rotated on a regular basis, tires will typically wear out in pairs rather than in sets. And if the tires aren't rotated at all, it's likely that the rear tires will still have about 1/2 of their original tread depth remaining when the front tires are completely worn out.
Intuition suggests that since the front tires wore out first and because there is still about half of the tread remaining on the rear tires, the new tires should be installed on the front axle. This will provide more wet and wintry traction; and by the time the front tires have worn out for the second time, the rear tires will be worn out, too. However in this case, intuition isn't right...and following it can be downright dangerous.
"When tires are replaced in pairs...the new tires should always be installed on the rear axle and the partially worn tires moved to the front."
When tires are replaced in pairs in situations like these, the new tires should always be installed on the rear axle and the partially worn tires moved to the front. New tires on the rear axle help the driver more easily maintain control on wet roads since deeper treaded tires are better at resisting hydroplaning.
Hydroplaning occurs when the tire cannot process enough water through its tread design to maintain effective contact with the road. In moderate to heavy rain, water can pool up in road ruts, depressions and pockets adjacent to pavement expansion joints. At higher speeds, the standing water often found in these pools challenges a tire's ability to resist hydroplaning.
Exactly when hydroplaning occurs is the result of a combination of elements including water depth, vehicle weight and speed, as well as tire size, air pressure, tread design and tread depth. A lightweight vehicle with wide, worn, underinflated tires in a heavy downpour will hydroplane at lower speeds than a heavyweight vehicle equipped with new, narrow, properly inflated tires in drizzling rain.
If the front tires have significantly less tread depth than the rear tires, the front tires will begin to hydroplane and lose traction on wet roads before the rear tires. While this will cause the vehicle to understeer (the vehicle wants to continue driving straight ahead), understeer is relatively easy to control because releasing the gas pedal will slow the vehicle and help the driver maintain control.
However, if the front tires have significantly more tread depth than the rear tires, the rear tires will begin to hydroplane and lose traction on wet roads before the fronts. This will cause the vehicle to oversteer (the vehicle will want to spin). Oversteer is far more difficult to control and in addition to the initial distress felt when the rear of the car starts sliding, quickly releasing the gas pedal in an attempt to slow down may actually make it more difficult for the driver to regain control, possibly causing a complete spinout.

Experience

Members of Tire Rack team had the chance to experience this phenomenon at Michelin's Laurens Proving Grounds. Participants were allowed to drive around a large radius, wet curve in vehicles fitted with tires of different tread depths -- one vehicle with new tires on the rear and half-worn tires on the front and the other with the new tires in the front and half-worn tires on the rear.
It didn't take long for this hands-on experience to confirm that the "proving grounds" name for the facility was correct. The ability to sense and control predictable understeer with the new tires on the rear and the helplessness in trying to control the surprising oversteer with the new tires on the front was emphatically proven.
And even though our drivers had the advantage of knowing we were going to be challenged to maintain car control, spinouts became common during our laps in the car with the new tires on the front and the worn tires on the rear. Michelin advises us that almost every driver spins out at least once when participating in this demonstration!
Experiencing this phenomenon in the safe, controlled conditions of Michelin's Laurens Proving Grounds rather than in traffic on an Interstate ramp in a rainstorm is definitely preferred!

Recommendations

Tires should be serviced periodically following the rotation patterns provided in the vehicle's owner's manual or as established by the industry to help enhance wear quality and equalize front-to-rear and side-to-side wear rates. The minor differences in tread depth between tires that might be encountered immediately after periodic tire rotations at 5,000-7,500 mile intervals won't upset the vehicle's hydroplaning balance and should not preclude rotating tires. For that matter, any differences in wear rates actually indicate that tire rotations should be done more frequently. Ideally tires should be replaced in complete sets. However when tires are replaced in pairs, the new pair of tires (assuming the vehicle is equipped with the same size tires all of the way around) should always be installed on the rear axle and the existing partially worn tires moved to the front axle.
While insufficient tire rotation intervals and/or out-of-adjustment wheel alignment angles often caused the differences in front-to-rear and side-to-side tire wear rates in the first place, the need to keep deeper treaded tires on the rear axle to resist oversteer conditions caused by wet road hydroplaning is important. Unfortunately this precludes the future possibility of ever rotating tires.
Once a pair of tires has been installed, the only way to escape being forced to drive on mismatched tires continually is to install a complete set of new tires (especially on front-wheel drive vehicles).

Friday, 19 June 2015

The Benefits Of Nitrogen Inflation for tire.

Tyres runs cooler, last longer and improve handling & braking. Quieter tyre - muting more road noise.
For some years, inflating tyres with nitrogen has been known to produce some substantial advantages over conventional compressed air. Its use has been limited to specialised applications such as aircraft tyres and motorsport, mainly on the grounds of cost of equipment and difficulty of generating this inert gas on the premises.

R-Tec are pleased to announce that the benefits of nitrogen inflation are now available at our workshop.

The main advantages of Nitrogen Inflation for tyres are as follows:
Tyre Inflation Pressure Remains More Stable
It is normally recommended that tyre pressures should be checked (including the spare tyre) monthly, and before any long trip. With nitrogen inflation, natural pressure loss is less and the interval for adjusting pressures is considerably extended. However, it is naturally still prudent to check your tyre pressures at the recommended intervals and particularly the pressure of any suspect tyre.
Condensation On The Inside Of Wheels Is Drastically Reduced
One of the most common everyday problems we face is corrosion on the inside of steel and alloy rims. This leads to leaking around the rim with corresponding suspicion of a slow puncture.The introduction of nitrogen inside the tyre prevents oxidization which causes a rapid ageing of the tyre and corrosion inside the rim.
The Possibility Of A Blow Out Or Explosion Is Reduced
Nitrogen doesn't heat up like oxygen, the tyre therefore runs cooler and thus reduces the possibility of explosion.
Better Grip On The Road
Nitrogen being far more stable in respect of temperature and pressure translates into better grip and improved vehicle handling. There are also proven reports of extended tyre life, making nitrogen inflation very cost effective. In addition to the benefits for most road users, nitrogen inflation has particular benfits for caravan, camper and trailer users. Better pressure retention and a reduction in the ageing process are real benefits for these vehicles which often spend a great deal of time standing in one place.

So what should drivers do?

Overall, inflating tires with nitrogen won't hurt them and may provide some minimal benefits.
Is it worth it? If you go someplace that provides free nitrogen with new tires, why not? Additionally we've seen some service providers offering reasonable prices of about $5 per tire (including periodic adjustments for the life of the tire) to a less reasonable $10 per tire (with additional costs for subsequent pressure adjustments) or more as part of a service contract, which we believe exceeds the value of nitrogen's benefit.
Rather than pay extra for nitrogen, most drivers would be better off buying an accurate tire pressure gauge and checking and adjusting their tire pressures regularly.

Tuesday, 16 June 2015

When Should you Replace your Tires?在什么状况下该换掉你的轮胎呢???

tread-depth-guide.png (422×248)
A driver's ability to control their vehicle depends on the traction between their tires and the road. Tires don't require tread designs or even much tread depth to deliver traction on dry roads. A practical example of this is the racing slicks used on stock cars and open-wheel racers that provide traction at over 200 mph. However, tires do require tread designs to generate traction on wet, slushy and snow-covered roads. Liquids can't be compressed and require time and energy to move them out of the way as our tires drive through them. Those same racing slicks would lose traction at amazingly slow speeds anytime something prevented them from maintaining contact with the road.
So a tread design is necessary to direct water and slush from between the tire and the road, as well as provide edges that bite into snow. But that's only half the equation; because we've seen that tread depth also contributes to how well the design does its job.
The air our tires encounter at highway speeds can easily be compressed and moved out of the way with relative ease. However the same isn't true of liquids. When water collects on the road surface during rainstorms, the water depth, vehicle speed and vehicle weight, as well as the tires' tread designs and tread depths collectively determine when and if the tires will be forced to hydroplane and how quickly they can stop a vehicle.
"Tire Rack's advice is that if rain and wet roads are a concern, you should consider replacing your tires when they reach approximately 4/32" of remaining tread depth."
A typical passenger car tire has about twenty square inches of total footprint surface and begins with about 1/3" of tread depth. While the majority of the footprint surface is made up of the rubber that grips the road, the remainder is the void of the grooves that make up the tread design. (See Photo #2)

In order to confirm how much wet traction worn tires sacrifice, members of the Tire Rack team measured the stopping distances from 70 mph (the typical speed limit of U.S. Interstate highways) with vehicles equipped with sets of new tires and compared them to tires with about 4/32" (3mm) of remaining tread depth, followed by sets with the legal minimum of 2/32" (1.6mm) depth. The differences surprised us! Vehicles equipped with the 2/32" minimum tire tread depth took about 100 more feet to stop and were still traveling at about 45 mph at the same distance the vehicles equipped with the 4/32" deep tires had already come to a complete stop!Obviously the tread will wear away over the life of the tire and the volume of its tread grooves will be reduced. While this occurs so slowly that it may not be noticed day-to-day, ultimately there will be a time when the driver will notice the car slip in the snow, hydroplane in the rain or simply not stop in as short a distance on wet roads.
The Tire Rack's advice is that if rain and wet roads are a concern, you should consider replacing your tires when they reach approximately 4/32" of remaining tread depth. Since water can't be compressed, you need enough tread depth to allow the rain to escape through the tire's grooves. If the water can't escape fast enough, your vehicle's tires will be forced to hydroplane (float) on top of the water, losing traction and increasing stopping distances.
Additionally, if snow-covered roads are a concern, you should consider replacing your tires when they reach approximately 5/32" of remaining tread depth to maintain good mobility. You need more tread depth in snow because your tires need to compress the snow in their grooves and release it as they roll. If there isn't sufficient tread depth, the "bites" of snow your tires can take on each revolution will be reduced to "nibbles," and your vehicle's traction and mobility will be sacrificed.
While replacing your tires before they are legally worn out may not appear the most economical practice, it is far less expensive than repairing your car if it can't stop in an emergency situation in less distance than the vehicle ahead of you!

Saturday, 13 June 2015

Tire Rolling Resistance Part 3: Changes to Expect When Switching from Worn-Out to New Tires


New, Full-Treaded Tires Generate More Rolling Resistance Than Shallow-Treaded, Worn Tires

Tire rolling resistance gradually drops by about 20% during the life of a tire as the tread wears from its original molded depth to worn out. This can be attributed to the reduction in tread mass and rubber squirm, as well as subtle hardening of the tread compound during years of service and exposure to the elements.
While this gradual reduction in tire rolling resistance and minor increase in fuel economy may be too subtle to register during the tire's life on a tank-by-tank basis, the virtually instantaneous switch from worn tires to new tires (even if they are the same brand, type and size) will typically result in an increase in rolling resistance of about 20%. Since the automotive industry estimates a 10% increase in tire rolling resistance will result in a 1% to 2% decrease in vehicle fuel economy, drivers should expect to experience a potential 2% to 4% decrease in mpg.

New, Full-Treaded Tires Travel Farther per Tire Revolution Than Shallow-Treaded, Worn Tires

Vehicles are programmed with their Original Equipment (O.E.) tire's revolutions-per-mile to allow their odometers to calculate the distances traveled. Unfortunately vehicle odometers aren't always 100% accurate and the tire revolutions per mile will change as its tread wears.
The diameter and circumference of a new, full-treaded tire is greater than that of an old, worn-out tire. Considering that many passenger car tires are molded with beginning tread depths of 10/32" to 12/32", the tires will be approximately 1/2" to 6/10" shorter in diameter when they've worn to the minimum tread depth of 2/32".
In order to determine how much odometer error this dimensional difference might cause, the Tire Rack team drove one of our 2008 BMW 328Ci test cars on a set of new, full-treaded 205/55R16-sized tires, as well as another set of the same tires shaved to worn-out (2/32") tread depth. We used a Global Positioning System (GPS) to measure the 100-mile test distance on a dry Indiana Toll Road and maintained an average speed of 70 mph. We then compared the number of miles traveled indicated by the vehicle's odometer to the GPS receiver and highway mile markers.
When the GPS indicated exactly 100 miles had been traveled while the vehicle was equipped with new 12/32" deep tires, the vehicle's odometer registered 99.4 miles. When the vehicle was then equipped with another set of the same tires shaved to 2/32" of remaining tread depth, the odometer indicated 101.0 miles. While the 100-mile test distance didn't change, essentially the vehicle's odometer overstated the distance traveled by about 1.5% when equipped with the worn out tires.
Since drivers traditionally monitor their vehicle's fuel economy by dividing the number of miles traveled as registered on the odometer by the number of gallons used to fill the tank (or by simply letting the vehicle's trip computer handle the task), the accuracy of the vehicle's fuel economy calculation is dependant on the number of miles indicated by the odometer.
This means that the vehicle's fuel economy (whether calculated by the driver after filling up or the trip computer) would instantaneously appear to drop by about 1.5% when fitted with new tires simply because the vehicle would actually have traveled 1.5% farther than it did when equipped with its recently removed worn-out tires.

Not All Tire Dimensions are Created Equal

Even though tires may be branded as the same size, their specifications may vary slightly by manufacturer and tire line. Tire Rack has seen the overall diameter of a single passenger car tire size vary by 2/10" from the smallest to the largest.
As an example, we'll compare the differences between an O.E. tire with two replacement tires in the 185/65R15 size used on the 2008 Toyota Prius,
DiameterTread DepthTire RPM*
Goodyear Integrity (O.E.)24.4"10/32"855
Yokohama AVID TRZ24.4"11/32"850
General Altimax RT24.5"11/32"843
*Tire revolutions per mile

As shown above, there are slight differences between the tires' published diameters, tread depths and tire revolutions per mile. However, if a tire rolls fewer times per mile than the tire it replaces, the vehicle will again actually be traveling farther than is indicated by the odometer. Calculating the influence of the different tire specifications on the vehicle's odometer would indicate the Yokohama AVID TRZ would travel .6% farther than the Goodyear Integrity, while the General Altimax RT would travel 1.4% farther.

Conclusion

While many of these individual differences may seem insignificant, it is easy to understand that when they are added together, the new tires may appear to reduce vehicle fuel economy. It also means that a Toyota Prius appearing to get 50.0 mpg just before replacing its worn-out tires with new tires of the same brand, type and size, might be reduced to registering just 47.25 mpg afterwards, even if all of the driving conditions were identical.
Remember, "your mileage may vary."

Monday, 8 June 2015

Tire Rolling Resistance Part 2: Defining Rolling Resistance

Tire rolling resistance is primarily linked to the deformation of the tire while rolling
Tire rolling resistance is defined as the force required to maintain the forward movement of a loaded pneumatic tire in a straight line at a constant speed. And just like the laws of physics and forces of nature, it is an obstacle every vehicle has to overcome to transport passengers and cargo to their destinations.
Tire rolling resistance is caused by the natural viscoelastic properties of rubber along with the tire's internal components constantly bending, stretching and recovering as they cycle between their loaded (where the tread footprint flattens against the road) and unloaded states. The final contributor to tire rolling resistance is the tread's interaction with the road.
"Tire rolling resistance has an impact on vehicle fuel consumption estimated to range from about 4% during urban driving to 7% during highway driving."
The tread area represents a new tire's single largest and heaviest region and is the greatest contributor to tire rolling resistance. The tread and its underlying plies typically account for about 2/3 of a new tire's rolling resistance, while the sidewall and bead area represent the remaining 1/3.
Larger tires require more rubber and longer reinforcing cords than smaller tires. Therefore within a single tire model line, there is typically a relationship between tire size, weight and the resulting rolling resistance force where larger tires have more rolling resistance than smaller tires.
The most common laboratory test measures the force required to rotate a tire at 50 mph against a large diameter steel drum. Multiple samples of each tire size/model are tested to establish an average rolling resistance value. And since tire rolling resistance typically declines moderately as tire temperatures rise from cold to normal operating conditions during the first 30 minutes of driving every time the vehicle is used, values are recorded in the laboratory after operating temperatures and rolling resistance values stabilize.
Tire Rolling Resistance Force is measured in pounds or kilograms of resistance. Comparing Rolling Resistance Force provides a direct way to compare tires of the same size, as well as offers an accurate means of comparing differently sized tires to one another.
Tire Rolling Resistance Coefficient is calculated by dividing the measured rolling resistance force by the tire size's prescribed load during the test. Comparing Rolling Resistance Coefficients only allows comparing tires within a single size. Tire Rolling Resistance Coefficient does not allow comparing different sized tires.
As noted earlier, larger tires generate higher Rolling Resistance Forces than smaller tires. However the larger tire's greater overall diameter, circumference and rolling radius allows its tread area to bend, stretch and recover more easily as it cycles in and out of contact with the road. Larger diameter tires also revolve fewer times per mile and cycle at a slower rate than shorter tires for any given speed. While this essentially reduces Rolling Resistance Coefficient (larger tires will often have a lower Rolling Resistance Coefficient than smaller tires), it still does not change the fact that a larger tire actually generates more Rolling Resistance Force that the vehicle's engine has to overcome.
Unfortunately comparing tire Rolling Resistance Coefficients is somewhat like comparing the fuel efficiency of an 8 passenger, 15 mpg sport utility vehicle to a 4 passenger, 30 mpg car based on miles per gallon per passenger when fully occupied. While both vehicles offer the same miles per gallon per passenger fuel efficiency when fully occupied, the sport utility vehicle will always use more fuel than the car (as well as more fuel per passenger anytime the sport utility vehicle is driven below its maximum passenger capacity).
Regardless of their calculated Rolling Resistance Coefficients, aunds of Rolling Resistance Force will require more energy to roll than a small tire generating 15 pounds of Rolling Resistance Force.
Tire rolling resistance has an impact on vehicle fuel consumption estimated to range from about 4% during urban driving to 7% during highway driving. The engine and driveline is estimated to consume 80% of the fuel, while the remainder is used to overcome inertia, wind resistance, converted into heat by the brakes or consumed when the vehicle is idling. The automotive industry estimates a 10% reduction in tire rolling resistance will result in a one to two percent improvement in vehicle fuel economy. While that might not seem like a lot, it can reduce fuel consumption by a couple of tanks per year and make the purchase of lower rolling resistance tires a better value over their lifetime.